- 1 How do I change the settings on my Oral B toothbrush?
- 2 How does the timer work on Oral B toothbrush?
- 3 How do I set the timer on my Oral-B toothbrush?
- 4 Why is my Oral-B toothbrush not working?
- 5 How do I turn on Oral B Smart Guide?
- 6 How do I connect my Oral B toothbrush?
- 7 Does my Oral-B toothbrush have a timer?
- 8 Why does my Oral-B electric toothbrush turn on by itself?
- 9 Why does my electric toothbrush pause?
- 10 Why does my electric toothbrush stop spinning?
How do I change the settings on my Oral B toothbrush?
Turn on the toothbrush using the on/off button – it will start in Daily Clean mode. To switch to the other modes, press the on/off button again. Keep pressing it to cycle through the brushing modes your toothbrush has. To turn the toothbrush off, hold the on/off button until the brush stops.
How does the timer work on Oral B toothbrush?
From the moment the brush is turned on, a built-in timer is activated. At the end of the 2 minute cleaning cycle, the motor in the brush pauses and restarts briefly three times. This pausing of the brush motor causes the brushing sensation to change as well as the sound of the brush.
How do I set the timer on my Oral-B toothbrush?
Personalizing the timer Your toothbrush comes with the «Professional» and «Count up» timer activated. To change this, press and hold the brushing mode button for 3 seconds until the SmartGuide shows «:30» and «timer». Briefly press the on/off button to switch to the «2-Minute» timer. Push the mode button to confirm.
Why is my Oral-B toothbrush not working?
The best thing to do is to put it on the charger for 30 minutes or so, and then try to switch it on. It should blink green during charging. Note that this can take up to 15 minutes to start happening if the toothbrush was entirely drained of battery during brushing. When charging is complete, the blinking should stop.
How do I turn on Oral B Smart Guide?
- Open the battery compartment of your Smart Guide and hold down the ‘h/min’ button for 3 seconds until the display starts flashing ‘L ‐ ‐ ‐’
- Switch on your toothbrush for a few seconds until the SmartGuide displays ‘L ‐ 1 ‐’
- Switch off your toothbrush.
How do I connect my Oral B toothbrush?
Tap “START” on the welcome screen. Press the power button on your electric toothbrush once to activate Bluetooth. The app will let you know when your electric toothbrush has been located. You can turn off your electric toothbrush after it has successfully connected to the app.
Does my Oral-B toothbrush have a timer?
Most Oral-B rechargeable electric toothbrushes have built-in two-minute timers, and some even have professional timers that parse out 30 seconds for each quadrant to help you keep track.
Why does my Oral-B electric toothbrush turn on by itself?
Oral-B toothbrush power cycles on/off If the Oral-B toothbrush is turning itself on and off very quickly, and then continues to run this likely normal. This is the professional timer, also known as the pacer/quadpacer/30 second timer.
Why does my electric toothbrush pause?
At the end of the 2 minute cleaning cycle, the motor in the brush pauses and restarts briefly three times. This pausing of the brush motor causes the brushing sensation to change as well as the sound of the brush. This is your signal that the 2 minutes of brushing time has been achieved.
Why does my electric toothbrush stop spinning?
If the replacement brush head is not moving, and the toothbrush is definitely switched on (because you can hear it), the first thing to do is try another replacement brush head. This rules out that the brush head itself is the issue. Next, have a look at the metal shaft under the brush head.